FAAC GATE OPENER REPAIR
FAAC gate openers are known for their durability and advanced technology. Our expert technicians provide comprehensive repair services to ensure your FAAC gate opener remains reliable and secure. Below, you can find detailed information on the services we offer for specific FAAC models.
We repair FAAC gate openers throughout the San Francisco Bay Area and Peninsula, with same-day service in Atherton, Menlo Park, Palo Alto, Los Altos, as well as Hayward, Castro Valley, San Leandro, Fremont, and the greater East Bay. If your FAAC hydraulic or electromechanical operator needs service, call 510-458-2048.
FAAC 760 SERVICE & REPAIR
FAAC 760 Service & Repair - The FAAC 760 is an underground hydraulic swing gate operator, buried below the gate pivot so it stays nearly invisible on large ornamental gates. It runs on 115/230V and uses hydraulic locking to hold the gate closed. FAAC has discontinued it in favor of the S800H, but we keep 760 systems running with full rebuild and repair service.
- Complete system rebuilding
- Hydraulic fluid replacement
- Motor replacement
- Sensor adjustment
- Control board diagnostics
- Routine maintenance
- Seal replacement
- Pressure adjustments
FAAC 750 SERVICE & REPAIR
FAAC 750 Service & Repair - The FAAC 750 is an in-ground hydraulic swing operator (115/230V) built for residential ornamental gates with leaves up to approximately 13 ft and roughly 1,760 lb each. It's self-lubricating, uses a hydraulic lock, runs quietly, and stays nearly out of sight below the pivot. Still sold today as a legacy unit, and we service every part of it from the hydraulics to the electronics.
- Hydraulic lines replacement
- Motor repairs
- Electronic diagnostics
- Hydraulic fluid replacement
- Control board diagnostics
- Troubleshooting of common issues
- Routine maintenance
- Replacement of worn components
FAAC S800H SERVICE & REPAIR
FAAC S800H Service & Repair - The S800H is FAAC's current underground hydraulic swing operator and the modern successor to the 760. It uses hybrid 24V DC technology with a magnetic encoder and BUS 2easy safety wiring, and handles leaves up to approximately 13 ft and roughly 1,760 lb. We provide full service including hydraulic unit maintenance and encoder/sensor calibration.
- Hydraulic unit maintenance
- Sensor calibration
- Control board diagnostics
- System re-calibration
- Motor replacement
- Sensor adjustment
- Control board diagnostics
- Routine maintenance
FAAC S450H SERVICE & REPAIR
FAAC S450H Service & Repair - The S450H is a compact 24V DC surface-mount electro-hydraulic swing operator that drives the gate with a linear ram. This hybrid unit uses encoder feedback and handles leaves up to approximately 14 ft and roughly 1,100 lb, running on the 24V E124 control board. We provide full repair and maintenance to keep it operating smoothly.
- Hydraulic unit repair
- System diagnostics
- Routine maintenance
- Replacement of worn components
- Motor replacement
- Sensor adjustment
- Control board diagnostics
- Routine maintenance
FAAC 455D, 452 MPS, E124
FAAC Control Board Repair (455D, 452 MPS, E124) - These are FAAC swing-gate control boards. The 455D is the current high-voltage (115/230V) board and drives single or master/slave dual-leaf setups, replacing the older 452 MPS, which is now discontinued. The E124 is the current 24V DC board and runs FAAC's low-voltage motors like the S450H, S800H, and 412 with BUS 2easy and encoder safety. We troubleshoot, repair, and replace all three.
- Control board diagnostics
- Circuit testing and repair
- Firmware updates
- Underground sensor troubleshooting
- Loop detector adjustments
- Remote control programming
- Safety system reconfiguration
- Component replacement
FAAC E145, E045, E700
FAAC E-Series Control Board Repair (E145, E045, E700) - The E145 and E045 are 230V swing-gate boards, both now discontinued and replaced by the E145S and E045S. The E700 is a different animal: it's the sliding-gate control board built into FAAC's 740 and 741 electro-mechanical slide operators, not a swing board. We diagnose and repair all of these electronic systems for reliable gate operation.
- Electronic diagnostics
- Circuit board repair
- Logic controller testing
- Firmware troubleshooting
- Input/output configuration
- Parameter reprogramming
- Component replacement
- System calibration
FAAC Model List
We repair the full FAAC lineup. Here's how the models break down:
- Underground hydraulic swing: 760 (legacy)
- Underground hydraulic swing: 750 (legacy)
- Underground hydraulic swing: S800H (current)
- Surface hydraulic swing: S450H (24V DC)
- Surface hydraulic swing: 400 (115/230V AC)
- Control board: 455D (current, high-voltage)
- Control board: E124 (current, 24V DC)
- Control board: 452 MPS (legacy)
- Control board: E145, E045 (legacy)
- Control board: E700 (sliding gates)
If your FAAC model isn't listed here, call us at 510-458-2048 and we'll help you sort out the repair.